On optical flow techniques applied to breaking surges

Surface wave breaking is a challenging two-phase flow process which plays an important role in numerous physical processes. A highly-turbulent unsteady breaking surge was investigated experimentally in a large facility, and substantial aeration occurred in the roller. The application of three optical flow techniques (Lucas-Kanade, Horn-Schunck and Farnback) to the air-water region was tested. The results indicated that the Farnback technique provided most accurate results, although some misleading results could be obtained near the air-water boundaries of the roller. The bore generation by a rapid gate closure showed a highly-unsteady complicated velocity field, with substantial free-surface deformations, wave breaking and formation of large coherent structures before the surge detached from the gate. Further upstream, the surge propagated as a hydraulic jump in translation and the data showed a marked shear region with a recirculation zone above, showing air-water flow features comparable to stationary hydraulic jumps. The upper and lower bounds of air-water flow region yielded data implying an air-to-water velocity ratio about 4–5 for a Froude number Fr₁ = 2.1.     

Evolution of linear edge dislocation in atmospheric turbulence and free space

In accordance with the extended Huygens–Fresnel principle, the evolution of linear edge dislocation propagating through atmospheric turbulence is studied, and the effects of waist width and the slope of linear edge dislocation are investigated. It is shown that when linear edge dislocation beams propagate through atmospheric turbulence, if the waist width is not equal and the slope is not zero, then the linear edge dislocation vanishes and transforms into an optical vortex with a topological charge of ?1 or +1. The optical vortex and an optical vortex that is created annihilate when the transmission distance is far enough. The linear edge dislocation vanishes when the slope is zero. If the waist width is equal, then the linear edge dislocation will vanish regardless of the slope value. For linear edge dislocation beams in free space, when selecting specific parameters, linear edge dislocation always exists.     

Extending social responsibility to small and medium-sized suppliers in supply chains: A fuzzy-set qualitative comparative analysis

Buying firms’ sales and reputation will be greatly damaged by any non-responsible behaviors on the part of suppliers, especially when those suppliers, like small and medium-sized enterprises (SMEs), have restricted resources and capabilities. To eradicate these risks, a growing number of buying firms have introduced socially responsible supplier development (SRSD). SRSD, including monitoring and evaluating suppliers, can provide them with incentives and assistance. Based on configuration theory and contingency theory, fuzzy-set qualitative comparative analysis (fsQCA) is adopted in this study to examine how SRSD practices adopted by buying firms, supply chain partnership, and market turbulence affect the corporate social responsibility (CSR) performance of their SME suppliers. We find that, as core factors, supplier monitoring, supplier assistance, and supply chain partnership can work together with peripheral conditions to achieve superior CSR performance. In addition, even at different levels of market turbulence, superior CSR performance can be realized through different causal configurations.     

Application of the sampling moiré method to shallow open-channel flows with circular roughness elements

This research presents an application of the sampling moiré method, a novel technique originally developed for measuring slight deformation of a static object such as a plate, to fluctuating free water surface in rough open channel flows. The method was used to capture the two-dimensional water surface deformation at a high sampling rate by dyeing the color of water white. The target flow was a very shallow subcritical flow with a depth of 1.5 times the height of the roughness. As a result, a series of instantaneous water surface profiles with non-uniform rough planes were successfully measured at a sampling rate of 100 Hz.It has become clear that the effect of dispersive gravity waves traveling on the water surface is greater than that of non-dispersive waves driven by the turbulence, and that this feature becomes more pronounced as the Froude number increases in such shallow flow conditions. Furthermore, it was experimentally and theoretically verified that the intensity of water surface fluctuation increases with the square of the Froude number. The decomposition of surface fluctuations due to gravity waves and subsurface turbulence using the wavenumber frequency spectrum revealed that the effects of subsurface turbulence are about 20%. This is much less than the contribution from gravity waves in very shallow flows as in this experiment.     

发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。     

应用独立分量分析的激光测风雷达湍流频谱分解

针对大型风力发电机机组中常见的脉动湍流、风机尾流与涡流等湍流信号,研究了利用自然梯度下降的独立分量分析方法的湍流频谱分离效果,以区分中心风速与湍流信号,提高风机机组的综合工作效率。首先分析了风机组中常见湍流信号的后向散射与频谱分布特点,然后依据这些特点设计了对应的独立分量分析模型。在仿真结果符合要求的基础上,进行了双目激光雷达天线的风速采集与实际分离效果检测。实验结果表明,在大气折射率结构常数C2n≤10-14同时广义大气常数α≥4的通常情况下,利用双目信号能够分离出一个湍流中心和一个中心风速。对1 s内两个谱峰的波动范围进行统计,获得(2.59±0.05)MHz的中心风速以及(1.22±0.19)MHz的湍流中心估计,且二者的平均信噪比分别为25.93 dB和31.01 dB,能够在获得稳定的中心风速估计的同时得到一个较为稳定的湍流中心估计。     

DZZ5型自动气象站多媒体故障排查系统的设计与研发

为更有针对性地进行故障排除工作,文章设计研发了一款多媒体软件平台,嵌入细化后的DZZ5型自动气象站各观测要素的故障排查流程,并在相应故障检测节点中添加文字、图片和操作视频。用户可按照流程逐一进行排查操作,或者搜索关键字查看节点内容。同时提供带有关键字查询功能的故障实例库,供基层装备保障业务人员参考。     

Primary energy demand and energy costs of fixed-bed drying using the example of chamomile flowers

Abstract

Energy use efficiency in the drying of medicinal and aromatic plants is largely determined by weather conditions and process parameters. While the former are beyond control, the latter can be optimized. In order to achieve such optimization, different energy supply variants, based on typical operating conditions of batch-type grate drying in Thuringia, Germany, were analyzed. It was found that partial air recirculation and integration of heat pumps allow substantial savings in primary energy. However, under the constraint of German energy prices, significant savings in energy costs can only be achieved if combined heat and power generation systems are applied at the same time.     

5×5棒束通道内流动转捩特性研究

棒束通道的特殊结构导致其内部流动转捩情况较为复杂，探究其内部流动转捩规律具有重要意义。本文针对棒束通道内的流动转捩特性开展实验与CFD模拟研究，通过实验获得了棒束通道内沿程阻力系数的变化规律；采用不同湍流模型进行了数值模拟。结果表明，SST k-ω模型能较好地反映实验结果。进一步对比了不同雷诺数工况下通道内不同位置的沿程阻力系数与湍流强度，发现对于不同子通道，中心子通道湍流强度与沿程阻力系数高于边角子通道；对于同一子通道，子通道中心处湍流强度与壁面切应力高于子通道边缘处。这一结果说明，受壁面影响，棒束内湍流强度、壁面切应力、阻力特性具有不均匀性，这些空间上的不均匀性相互作用会引起总体上棒束转捩点不明显。     

Investigation on the flow characteristics of a novel multi-blade combined agitator by time-resolved particle image velocimetry and large eddy simulation

We investigated the flow characteristics in a tank of H/T = 1.5 stirred by a novel multi-blade combined agitator (MBC) by using time-resolved particle image velocimetry and large eddy simulation approach. The predictions were assessed by Y⁺ values, Taylor microscale and power spectrum analysis, as well as experimental validation of velocity distributions. Results demonstrate that the MBC agitator can load the energy into the system effectively with a power number of 12.5 in a turbulent regime, resulting in improved axial and radial mass exchange. The upper and lower short blades produce an axial down-flow in the top half and an axial up-flow in the bottom half, respectively. Part of axial flows change to radial flows by the radial pumping of the long blades, meanwhile, the impingement of two axial flows improves the axial mass exchange. These flow characteristics lead to an obvious improvement in the turbulent kinetic energy distribution uniformity with higher turbulent intensity.